|
I just figured out how to perform a repeater bridged connection, but my mtu is to low to push xbox live i tried raising the mtu under Network at network configuration in basic setup using unbridged eth0 but that didn't work i'm kind new to dd-wrt but ...
Started by supermanNC on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at dd-wrt):
My mtu is to low to run xbox live on my 2nd router thats set in reapter bridged mode, My mtu is high enough on my first one.
Get smart.
|
|
Hi there... well, I am not a complete beginner as far as this subject is concerned, but this time I am stumped...
I want to set up a static IP for my server ... I have a Billion 400g Router , and the server connected via eth0.
This is the output from ...
Started by the gene on
, 7 posts
by 3 people.
Answer Snippets (Read the full thread at ubuntuforums):
Now I can at least talk....
Now I can at least talk to the server, but am still having problems there....
I have a linksys here is a snap shot of my setting one, the mapping wasnt there....
Have you setup your router's port range routing.
|
|
I'm not quite sure if the mailing list is the adequate place for this
but I can't think of where else to place it that will get the views of
anyone that could have an idea what is going on.
I have a sun ultra 30, in my current living situation i don...
Started by edistocy@gmail.com on
, 7 posts
by 3 people.
Answer Snippets (Read the full thread at omgili):
Noah
--
Posted automagically then something else is going on.
I will update this once I have it available.
Correctly some strange packets passed by from the linksys (if
any) yet it did not respond or route and the
linksys router.
|
Ask your Facebook Friends
|
On Sun, 16 Nov 2008 03:30:08 +0100, Kent West <westk@acu.edu
I'm running Debian Sid and have a Linksys WMP54GS.
I've never really understood networking, and definitely not wireless
networking.
I've been trying half a week to get this card working...
Started by Kent West on
, 6 posts
by 2 people.
Answer Snippets (Read the full thread at omgili):
MULTICAST MTU:1500 Metric:1
RX packets:53432 errors:0 dropped:0 overruns:0 frame:0: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:138 errors:0 BROADCAST RUNNING MULTICAST MTU....
|
|
Playstation 3 Online Anleitung - Installation, FAQ, Probleme Wichtig:
Lest euch zuerst bitte alles durch
Wenn ihr Probleme beim Connecten habt wäre es sehr hilfreich, auch zu wissen was ihr bisher versucht habt, wie euer Netzwerk daheim aussieht, wie ...
Started by KOBE A.K.A MAMBA on
, 20 posts
by 13 people.
Answer Snippets (Read the full thread at gamepro):
Subnetzmaske 255.255.255.0
Standard-Router 192.168.0.1
Primäre DNS 192.168.0.1
> MTU : automatisch > (03.06.2007 um 14:06 Uhr) Drahtlos > Scannen > Wähle mein linksys mit WEP 50% > Gib den WEP;
Ip Adresse 192.168.1.105
Subnetzmaske....
|
|
Wife and I are unable to send picture messages via our iPhones when connected to our 3G MicroCell. We can send regular text messages just fine, but MMS will not work.
If I power down the MicroCell and connect via standard AT&T 3G, we can send picture ...
Started by Microcellie on
, 23 posts
by 17 people.
Answer Snippets (Read the full thread at att):
Unfortunately I'm not familiar with MTu
And thank you for your assistance.
The strange this is, is that data used with an Actiontec router .
I would first try to see what the MTU value is set to.
Router.
|
|
This thread has been created to discuss, and troubleshoot a specific issue that we are investigating, which may affect some Sure Signal customers.
This issue presents the following symptoms: Poor audio quality on both outbound and inbound calls Particularly...
Started by George on
, 8 posts
by 7 people.
Answer Snippets (Read the full thread at vodafone):
Check your MTU settings
Log into your admin page for your router
Find the location....
I have a Linksys router, and in the menu pages, accessed to assign the Sure Signal with a DNS Server address via DHCP.
Thanks Here’s what I did to fix this.
|
|
Hey all. I am a computer consultant. As a result I have a home network already set up the way I need it. One of the most important pieces is my VPN router, which I use to VPN to my network when I am at a client.
When I first called I wasn't sure if I ...
Started by Lan_61 on
, 30 posts
by 16 people.
Answer Snippets (Read the full thread at att):
Doing as....
Hooked up my Linksys booted every device in network at least once.
Hooked up my Linksys router to Ethernet port 1 by changing the RG's IP address range so that I didn't have an IP conflict.
So that I didn't have an IP conflict.
Related shopping results:
|
|
On Fri, 7 Nov 2008 23:12:58 -0500, "RoseW" <wdmn@nshurontel.on.ca
Are there recommended web sites for FTP issues (forums, articles, whatever)
or newsgroups?
I have one server that has had connectivity issues this past week when I
connect with FTP...
Started by RoseW on
, 6 posts
by 2 people.
Answer Snippets (Read the full thread at omgili):
As this is the first time that "big" packets
are transferred in the protocol, a MTU setting that is too big can
cause packet fracturing....
One is a MTU problem.
In my experience, two things can cause this problem.
Or
transfer files.
|
|
On Thu, 18 Sep 2008 18:44:11 -0500 (CDT), Cheryl Homiak <chomiak@charter.net
Hi all.
I am running debian lenny beta 2 on a thinkpad t23 laptop with a prism 2.5
onboard card. My problem is that after installing, before I tried to do
anything ...
Started by Cheryl Homiak on
, 3 posts
by 2 people.
Answer Snippets (Read the full thread at omgili):
I had used
the linksys on another thinkpad t23 so I knew to use madwifi Mask:255.255.255.0
UP BROADCAST....
It actually does
connect and works but is only working considering what else is loaded .
I inserted my pcmcia linksys card.
|
