|
Years ago some hubs had holes into which oil was put to lubricate them. A friend even older than I has offered me a 10sp 531 RJ Quinn, which uses such hubs.
3 Questions
1. The holes shoud be covered with circlets of sprung steel with a little dimple which...
Started by eoinin on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at ctc):
(Blu-tack.
Another use for your old inner tubes I used a cable tie on a home made lubrication hole else fails, a good solution for this is a small lump of Blu-tack smoothed over the hole.
|
|
Hi all,
Today whilst filling my m200 I noticed that the knob was hard to turn, so i decided to flush the pen and lube the plunger. Lubrication (100% silicone grease) did not solve the problem at all and plunger is still squeeky and knob hard to turn.
...
Started by SpideRMaN on
, 21 posts
by 6 people.
Answer Snippets (Read the full thread at fountainpennetwork):
I don't know if it really helped much, but think if Eel inks are supposed to help trying ....
There is nothing much you can do by this method, if the actual lead screw actuating the piston needs lubrication with a glycerin water solution.
|
|
For the TechPB community, and owners of the Harley Davidson of Paintball, the Autococker.
Through much research, I've found that WGP manuals (and almost all other Autococker manuals) are TERRIBLE...the instructions for lubrication and maintenance in those...
Started by VICE_ROY on
, 34 posts
by 13 people.
Answer Snippets (Read the full thread at techpb):
If you have a ram that you can unscrew to disassemble (not take of the gun), do so! Clean and lube the inside of the ram... .
If you want to maintain everything and the kitchen sink, lubing the ram is also great .
VICE_ROY, on Nov 21 2008, 10:32 PM, said:
5.
|
Ask your Facebook Friends
|
We have recently had a large steel gate installed - typical Isaan style, on rollers, running along a steel track. The gate is 3+ metres long.
I am sure other members have similar gates at their properties. My question is - what do you use to lubricate...
Started by jackspratt on
, 15 posts
by 12 people.
Answer Snippets (Read the full thread at udonmap):
Tried WD40, and chain lube/Sonax, with neither lasting more than a week or two .
Is the best solution.
|
|
There is no way that we can lubricate ibm t43 fan . Its fully sealed any ideas about it . My t43 fan gave me some rattling noises i have soaked the fan totally in some oil and now its running silently i dont know how long its going to last , but its fully...
Started by kanewilliam on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at thinkpads):
Free tip: You may.
To oil a long fan without disassembling the heatsink? and T60 T61 fan lubrication - illustrated guide by msb0b inside and Total solution for absolutely ZERO oscillatory noise in T4x .
|
|
This is the 'truth' about how I followed the instructions on how to un-seize the clip mechanism on ReadyNAS NV+ disk trays; posted in Cabana as I don't want to distract from the excellent and sensible post on how to fix them ( located here )
NV+ Caveat...
Started by Briain on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at readynas):
Absolutely hilarious - and, I hope, true?? Hi
Well it started out as a quick note to let folks know the two types of tray are different (I think they've since been redesigned) and turned into a light hearted 'works instruction' on how to do it and the... .
|
|
On Sun, 26 Jul 2009 21:34:29 GMT, "SP" <Lesley@scorbydax.co.uk
What's the recommended lubrication for clutch cables nowadays?
Or should I just ignore the lube, and get a new cable. After all,
lubing is only a short-tem solution.
--
Lesley
Residing...
Started by SP on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at omgili):
On Sun, 26 Jul 2009 18:02:12 -0700 (PDT), zymurgy <zymurgy@technologist.com
On Jul 26, 10:34 pm, "SP" <Les...@scorbydax.co.uk
I use this stuff,
http://www.screwfix.com/prods/52410/Van-Car-Accessories/Car-Lubricants/3-In-One-Oil-Pro-Silicone-... .
|
|
On Thu, 28 May 2009 23:34:59 +0000 (UTC), Bob Bethune <poihths@comcast.net
So I took my 1911 out to the range over the weekend and shot about 50
rounds. No problems. Brought it home, finally decided to get around to
cleaning it tonight. I take it...
Started by Bob Bethune on
, 14 posts
by 7 people.
Answer Snippets (Read the full thread at omgili):
This situation
developed, but the solution has become to dress the slide rails
lightly with a diamond stone if I'll ever know why or how this situation
# developed, but the solution has become to dress the slide.
|
|
Ciba Clear Care (peroxide with neutralizer disc) was my preferred cleaning solution with my older contacts , but when I used it with Purevision I found that the lenses stuck to the basket and I almost had to peel them off. The lenses would tear after ...
Started by KenHirsh on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at lens101):
But I'll be mindful of the same concept: I use KenHirsh Ciba... .
But I'll be mindful solution for extra lubrication before I open the basket.
solution or my Aquasoft solution for extra lubrication before I open the basket.
|
|
So I got to try out my new to me blower this week using my new to me Diesel. Holy cow I never thought my 23 hp Kohler was under powered but after using the 24.5 hp diesel this things acts as if it is mad at the snow it throws it with so much force. I ...
Started by firefighter5143 on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at mytractorforum):
That was solved with some good lubrication.
Sticky so you had to manually bring them back to neutral .
|
