Discussions about pinch valves

Engine: Valves Getting ready to adjust valves on newly rebuilt 259. How can I adjust them while eng. is warmed up without oil running down the side of the engine and onto the floor/ I had an extra set of valve covers with the tops cut out years ago but they are long... Started by Tennessee hillbilly on Sunday, February 05, 2012, 19 posts by 11 people.   Read the full thread at studebakerdriversclub Discuss this with your friends on Facebook Answer Snippets (Read the full thread at studebakerdriversclub): The shop manual specifies adjusting valves with the engine running, so that's how I do it and have not had a problem with.... I have an original factory cover that will disagree with me . Always adjusted valves with the engine hot and running.

Opinion rt valves Which is the best rt valve and is the level ten neccessary if you have a warp/eggy set up 12vmod intell switch Started by river031403 on Friday, January 20, 2012, 11 posts by 5 people.   Read the full thread at automags Discuss this with your friends on Facebook Answer Snippets (Read the full thread at automags): Vmod intell switch All of the RT valves are the same in function, although the pins for the emags people's valves are faster than other people's valves, if there was a difference you would never be able.

Leaky valves stem seals? -an engineering solution!. Ok,this is a bit of a long tech post so hopefully people will get it.:confused: right,its becoming more apparent that more and more astra vxr owners are starting to suffer with leaky valve stem seals.myself included.i had mine done late last year,which... Started by PERCY'S vxr on Thursday, February 10, 2011, 10 posts by 8 people.   Read the full thread at vxronline Discuss this with your friends on Facebook Answer Snippets (Read the full thread at vxronline): Does this pinch the seal in place so it cannot even move a fraction of a mm? i did andy yeah,infact out,new stems in and all the valves.... Does this pinch the seal in place so it cannot even move. Stripped loads of those old engines apart.

NOS Valves - Fact or Fiction On Mon, 16 Feb 2009 06:38:47 -0800 (PST), Dave Benj <dave.benjafield@googlemail.com I've never bothered sourcing a set of original (NOS) 1950s/60s Mullard/ Phillips/Whatever valves for my Peavey Classic 50 - mainly because 4 x EL84s and 2 x 12AX... Started by Dave Benj on Monday, February 16, 2009, 5 posts by 5 people.   Read the full thread at omgili Discuss this with your friends on Facebook Answer Snippets (Read the full thread at omgili): There were duff valves fifty years ago too :) To be fair, Mullards are significantly better than.... Good in parts, mate. Guitar mate amp a year or so ago and it had the original valves in there (philips) so I thought I'd a curate's egg.

Valve amp - where to start? Valve amp - where to start? I am thinking about building a second system to use in my study at home. Its very small, c6ft x 10ft. Source could be Mac, Sonos or iPod touch. I could pinch some Linn Unik (88 w/db) speakers from elsewhere in the house to... Started by Martin J on Wednesday, February 01, 2012, 15 posts by 10 people.   Read the full thread at pinkfishmedia Discuss this with your friends on Facebook Answer Snippets (Read the full thread at pinkfishmedia): Source could be Mac, Sonos or .... If you want valves in a small room (with a small budget) - try this for size - 1) Refurbished Leak is normally considered the right level of efficiency for speakers intended to be used with valves? I had.

KlR 250 valve ticking after adjustment KlR 250 valve ticking after adjustment Yesterday I checked the valve settings on a 1995 KLR 250 I recently picked up. 7500 miles and I have no history of the maintenance, other than it looks clean and well cared for. From what I've read, it sounds like... Started by Everitt McGill on Wednesday, September 07, 2011, 19 posts by 10 people.   Read the full thread at klr650 Discuss this with your friends on Facebook Answer Snippets (Read the full thread at klr650): They'll under 6k or so, you won't need to check the .... Re: KlR 250 valve ticking after adjustment Make sure when checking the valves your at TDC the rear, intake valves open, then close, then watch the rotor as you turn the crank.

Holy Valve Job Batman! Just got back from a tour of a local machine shop.... and I saw this! why havnt I dont this?!?!? Before: New Bronze seat: Put it through its paces: and done: Quote: : Honda owners are the Jerry Riggers, we are the penny pinching jews of the automotive... Started by chromebeast on Wednesday, February 01, 2012, 10 posts by 8 people.   Read the full thread at neons Discuss this with your friends on Facebook Answer Snippets (Read the full thread at neons): Sweet Titanium valves next? Racing in motocross when swapping to titanium valves, for the bikes that dont come with titanium stock. Ported and polished valve ports in one easy(expensive) step.

3.2 running like crap after tune up/ valve adjustment So my wife got me the tune up kit for my 1987 3.2 and i decided to have at it. change the fuel filter, rotor, distributor cap, oiled the felt in the rotor shaft, changed the plugs, replaced penzoil 10w30 with brad penn, and did my first ever valve adjustment... Started by mark4ton on Saturday, January 28, 2012, 20 posts by 10 people.   Read the full thread at pelicanparts Discuss this with your friends on Facebook Answer Snippets (Read the full thread at pelicanparts): More I think about it, if you had the valves too tight, you.... It's difficult to adjust valves with worn guides, would it keep the valves open, but may be a possibility. Valves tight. Closed gap on a single plug. Or reversed.

Engine: Valve spring bind? What should the stock spring pressure be on a 289? What is the highest preload pressure you reccomend with shimming? What is the smallest feeler gauge you reccomend being able to insert between spring windings before it is a possible spring bind issue... Started by kmac530 on Thursday, January 26, 2012, 13 posts by 7 people.   Read the full thread at studebakerdriversclub Discuss this with your friends on Facebook Answer Snippets (Read the full thread at studebakerdriversclub): My machinist that cut that if I did that, the Ex valves.... Always a good check), and the OP concluded the higher performance cam must be making the valves collide other...however the exhaust valves are about 0.090" below the straight edge.

DIY adjusting valve clearences GD Well here it is the DIY everybody has been asking for setting the clearance of the valves in a GD Sorry I don't have photos of doing this in a USDM model with the different intake manifold that you can separate which makes this a much easier job. The ... Started by claymore on Sunday, March 13, 2011, 10 posts by 4 people.   Read the full thread at hondafitforums Discuss this with your friends on Facebook Answer Snippets (Read the full thread at hondafitforums): Each rocker pushed two valves by restricting your view and access to the.... This Saturday, mrFroge and I are planning to adjust the valves think? BTW, that bike required two feeler gauges per adjustment. Read that posts half a dozen times.