|
It is probably SDR pipe which, because of the thinner wall and the need to maintain an actual 3" i.d., means the o.d. has to be less than the standard sch. 40 pipe. The only fittings I have ever seen for it were bell and spigot push tight style and they...
Started by CM2304 on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at terrylove):
The ASTM number would lead you to the standard the pipe was manufacturedOne of those is....
The white pipe in the photo on it, I woudln't assume it was ...
I don't think it's junk at all - it's just different .
And it's PVC 1.
|
|
For a large wastewater project in North America, for large pipes (diameter 30"- 48"),under low operating pressure conditions, is it cheaper to use steel pipes instead of ductile iron pipes?
Thanks in advance
Answer Snippets (Read the full thread at eng-tips):
That pvc pipe burst, thereafter knocking the worker knocked off the ladder this account a maintenance worker fell from a ladder onto a 6" pvc drain pipe attached to a acid tank, "The force of ....
pvc water line.
|
|
Quote: : Plumber Those fittings are made by Viega. They use an o-ring. The crimp is applied by a special tool that is purchased from Ridgid or a few others.
My company has utilized this sytem since 2001. Not exactly new technology.
In my fine state of...
Started by Bob Elliott on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at nachi):
standard, not what home inspectors are "limited" to observe/inspect, or comment.
|
Ask your Facebook Friends
|
DH and I were at a home and garden expo type thing this afternoon and saw a booth for an electronic water conditioner. Apparently the thing is supposed to produce an electronic field in the pipes and not only keep the calcium and minerals from building...
Started by Blondesense on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at diychatroom):
The....
The answer is ...
Analysis: There are no formal standards governing the specification, installation or maintenance of such devices more time.
Is equipped with what appears to be a "Magnetic Water Treatment" (MWT) accessory.
|
|
Dear Friends
We are evaluating use of sand filled trenches for laying of fire water mains vis-a-vis burried design.
Request following information:
1. Is this design used in refining/petchem industry?
2. how do you protect the piping from external corrosion...
Answer Snippets (Read the full thread at eng-tips):
The pipe was supposed to be painted on how the pipe is ....
The code goes with the AWWA standards for steel pipe, but I´m not sure if going to ductil iron of corrosion and underground leaks and water mess around.
Not").
|
|
Need some winter watering set-up ideas for remote locations. Drought this past year really buggered up grazing plans, so some investment is needed this year on the water side.
All possible locations have no hydro or existing well/pressure system and I...
Started by Aaron on
, 6 posts
by 6 people.
Answer Snippets (Read the full thread at ranchers):
You cant build that just anywhere , but it sure worked good pump will deliver the... .
There was enough get to the water was in the pipe .
Burried a 16 inch pvc pipe along the ground with the top third cut off for about 2o ft.
|
|
Hi All,
Hopefully this long letter will help others, even if I get no good
answers.
My problem is how to get 3 showers a week in cloudy weather back in
the beautiful pucker brush where propane transport is a pain and a
coil in the wood stove not desired...
Started by humphill40@yahoo.com on
, 20 posts
by 9 people.
Answer Snippets (Read the full thread at omgili):
I'm not sure/alt.energy.homepower/browse_thread/thread/bca87aeee238a7f4?hl=en#
The water is heated in kettles on top of the wood, and not....
A PVC pipe run outside to provide enough air
for safe combustion, and this was in a house.
|
|
On Tue, 13 Jan 2009 11:59:56 -0500, "ng_reader" <wilgrow_co@hotmail.com
I will be doing some work in the laundry/heater room shortly, including
installing a new natural gas hot water heater.
At one time I had no problem doing my own plumbing "...
Started by ng_reader on
, 17 posts
by 9 people.
Answer Snippets (Read the full thread at omgili):
It probably has a fresh air intake be certified
to ULC S... .
This is usually just
a PVC pipe.
It must the need for the direct vent.
Vents for water heaters or
furnaces, you cannot use regular ABS, PVC or CPVC pipe.
|
|
I was wondering if anyone has tried doing this and if they were successful or not. If yes, can someone help me to construct one?
Thanks in advance!
Started by drkplayer122 on
, 14 posts
by 6 people.
Answer Snippets (Read the full thread at tennis-warehouse):
Quote....
Or buy something bigger.
Not sure why you'd want to bother with a pvc pipe construction.
Make sure you get the one a Schroeder valve, like on car tires .
Just remember, there are several types of PVC pipe.
The container.
Related shopping results:
|
|
Hello!
I had my kitchen sink drain clogged with flour and yeast and I had to use some drain cleaner (Line Cleaner) and a plunger. I got the whole thing unclogged but I noticed there was a little bit of drippings under the sink, where the P-trap is. I ...
Started by alex_nrv on
, 15 posts
by 5 people.
Answer Snippets (Read the full thread at diychatroom):
Sanding the PVC pipe....
Thanks for your input", but I've always known to sand PVC and copper pipes before welding or glueing.
pipe cleaner.
You can also use, after that, some pvc/cpvc/abs primer ...
That is abrasive.
|
