|
Where may I get algorithms to apply a plastic wrapping effect to an image?
I am using Visual C++.
Started by dev ray on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
This previous question touches base on similar image distortion effects and the groundwork for the effects, as far as your particular request, I do not know of any direct source
If you're looking to do something like a CD case or some other simple shrink... .
|
|
In the client drawing, it mentioned 85% translucency for the injected plastic.
How do we inspect if the plastic is 85% translucency?
Started by saisai on
, 8 posts
by 4 people.
Answer Snippets (Read the full thread at elsmar):
How do we inspect if the plastic is 85% translucency? Have a look at How to Measure Translucent Materials (PDF drawing, it mentioned 85% translucency....
|
|
Sanding plastic when sanding the plastics down for painting, do you need to use wet and dry paper?
Started by cliox4 on
, 11 posts
by 4 people.
Answer Snippets (Read the full thread at cliosport):
Re: Sanding plastic also approx how many cans of paint, primer, and laquer are needed for the front bumper side moulds and the side strips? Re: Sanding plastic Well you want to provide a key for your: Sanding plastic yeh im using ....
|
Ask your Facebook Friends
|
This black acrylic paint sucks for the plastic model I am building. What model paints should I be using?
Answer Snippets (Read the full thread at metafilter):
Make sure you give your plastic parts.
For large areas, I prefer spray enamels.
It with, well, thinner.
|
|
What are the pros and cons on using either a metal power pipe or a plastic one? The plastic ones seem to sell for half the price.
Started by SLOW5L on
, 13 posts
by 12 people.
Answer Snippets (Read the full thread at corral):
Ive got the UPR boostmaster (plastic) pipe and LOVE it! ive heared....
I'm in the same boat and I will go the plastic route on cost.
Metal one has better bling factor.
I would think the plastic would not absorb the heat like a metal one.
|
|
Hi,
Are you able to supply me with a pack, of approx 10 plastic clips/poppers that are used to hold the plastic panel that covers the top of the grill and radiator in place?
I ordered a set off eBay, but they were too big.
Cheers
Started by Saint2K on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at civinfo):
|
|
Rather than fret about things that I have no control over I have been painting dwarfs....
I cannot help but compare the Mantic Storm of Iron to the GW Thunderers. Both sets allow the choice between crossbows and guns, both are dwarfs, and that about runs...
Started by uncre8d1 on
, 30 posts
by 2 people.
Answer Snippets (Read the full thread at worldworksgames):
The plastic models had minimal mould lines.
The models are very nice and easy to assemble.
Avatars Of War are bringing out Plastic "Dwarf Berzerkers", which is very very to the positives.
Look, well, awkward.
|
|
Finally pulled the trigger and purchased the 47 inch blower for my x534. As I was unpacking the unit today I noticed the impeller is plastic not steel. I knew the chute was plastic but was surprised that the impeller would be plastic. Is this a recent...
Started by Mackx534 on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at mytractorforum):
Hopefully it can take a hit....
Can't imagine what it will do to a plastic impeller.
Got mine in October and was also suprised by the plastic impeller,
talked to JD , new in 2011 on 47 impeller a few times hitting ice that the plows throw out.
|
|
Guys can anyone tell me what blot or clip goes here in the pic,it the arch plastic bottom right hand side,behind there seems to be a thread which makes me think its a bolt that goes in there
Started by kenny rs on
, 8 posts
by 4 people.
Answer Snippets (Read the full thread at rsownersclub):
|
|
Okay, so I'm going to buy later, just doing some last second something...
Sirs, I would like to ask if what's better, I personally choose the Plastic ones because of it's lightness and it's cheapness.
So, what do you think sir?
Started by Avengerism on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at filairsoft):
I'll go for ICS M4A1 ICS M4A1 the best ano meron sa ics mga sir na wala sa jg m4 plastic version?.
|
