|
I'm adding coroutine support to an interpreter I'm writing and I'd like to do something like the following:
typedef enum { bar_stuff, bar_other } Bar; typedef enum { foo_error=-1, foo_none=0, foo_again } Foo_state; Foo_state do_foo(Bar bar,Foo_state foo...
Started by David X on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at stackoverflow):
Of the bar_ switch statement? Syntactically, it is valid (as long as the values are unique) but its poor.
|
|
Hello,
Not sure if this is the right place to ask this question. But I have a router which connects to the internet. Now I have a switch connected to this router. I added a lot more computers so I added another switch and connected it to the first switch...
Started by elated on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at serverfault):
Usually when I connect switches, I just use a regular cable because most of them switch remove everything from the second swtich and plug them in together put the second switch as the first one add another switch and plug both....
|
|
C#'s switch statement can compile to a CIL switch instruction, or if/else's, depending on the cases in the statement as mentioned here . Is there a way to force the compiler to always generate the if/else variant in a block of code?
Answer Snippets (Read the full thread at stackoverflow):
Have you tried a different compiler (i.e., Mono), or tried to place your offending classes in... .
EDIT that you're using a switch statement.
That makes it clearer to the reader that that's what you want to happen instead of using a switch.
|
Ask your Facebook Friends
|
Can a Cisco switch port be configured to communicate with another switch when the ports on each switch are on different vlans?
EDIT to add more details: The data center that we use has internal vlan numbers for their clients. This would provide internet...
Started by Richard West on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at serverfault):
Further, ....
It sounds like you want to cause a port on "switch A" to be a member of a different VLAN than the other ports on that switch (let's call those "VLAN 1" and "VLAN 2", respectively).
You want to do is going to be very difficult .
|
|
Just wondering if there is any hardware device that when it loses power, will send a remote signal to another power switch to turn off? This is more for media equipment, but I figured if anybody knew it would be here.
Started by esac on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at serverfault):
You could just use a smart switch (i dont know/PCs/4-/10674532/Lindy-Intelliplug....
In TV stations, there often are tally relays is configured to do something when the pulse comes in .
A command to inform another switch that the power is lost.
|
|
I want to know which message would show to the user in the following. I assume it would be both 11.2 and 11.3 because of the missing 'break' after case 7?
int d1 = 7; switch(d1) { case 6: printf("11.1 \n"); break; case 7: printf("11.2 \n"); case 8: printf...
Started by HollerTrain on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at stackoverflow):
A default case to your switch statement for when there's a mismatch (suppose d1 was 3 ...)
switch(d1.
|
|
What is your procedure when switching over an enum where every enumeration is covered by a case? Ideally you'd like the code to be future proof, how do you do that?
Also, what if some idiot casts an arbitrary int to the enum type? Should this possibility...
Started by Caspin on
, 14 posts
by 14 people.
Answer Snippets (Read the full thread at stackoverflow):
First of all, I would always have a default in a switch switch ing on and how bad an incorrect....
Rather than an enum value into your switch, and it's best to fail noisily but give the program option: Avoid switching over enums.
|
|
In Eclipse, I can switch through open editors using control-page up/down. This works great, except for editors like XML or JavaScript, where there are Design and Source tabs. For those editors, it just toggles between the different tabs. Is there any ...
Started by JW on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at stackoverflow):
I think it....
Which might sort of get you what you want, but is probably just as confusing as alt-F6 .
I was initially thinking alt-left and alt-right might do what you want, but that's more for going forward and backwards in history of tabs you've viewed .
|
|
In this question the answer was to flip on a switch that is picked up by the debugger disabling the extraneous header that was causing the problem. The Microsoft help implies these switched are user generated and does not list any switches.
<configuration...
Started by Darryl Braaten on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at stackoverflow):
You can use Reflector to search for uses of the Switch class and its subclasss (BooleanSwitch switch to ignore thread models --> <add name="AxIgnoreTM" value="false" /> <!-- Trace.
|
|
Can it be known in general whether or not placing a case within a for loop will result in bad assembly. I'm interested mainly in Delphi, but this is an interesting programming question, both in terms of style and performance.
Here are my codez!
case ResultList...
Started by Peter Turner on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at stackoverflow):
TComparer = class protected function Compare(const AItem1, AItem2: TItem): Boolean; virtual; abstract; public procedure DoCompare(ResultList: ...); end; TTextComparer = class (TComparer... .
Why not using subclasses?
This saves the use of the case statement .
|
