|
I had a brief exchange with Bob on tapers that got me thinking. I had always assumed that a 40 taper was a 40 taper, but he pointed out to me that there is a slight difference ISO tapers and NMTB tapers. The ISO tapers have an angle of 8.29722 degrees...
Started by Michael G on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at woodworkforums):
Wikki says "The taper is variously referred to as NMTB, NMT or....
On rate of taper to be 0.001 inch per foot applied only in the direction which decreases rate of taper from?
Fitting and machining says ISO-297 is a copy of the NMTB.
|
|
Is the 79 knuckle taper, the same as 1 ton chevy tie rod taper? I don't really need TRO, but I have all need front end steering parts save for the tie rods-draglinks so since I am replacing any way, I am going to up grade to RuffStuffs 1 ton ends while...
Started by mofoco1 on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at classicbroncos):
Wondering if the taper the reamer through, it was VERY close....
|
|
I think I already know the answer to this but I might as well ask,
I've got an xxtension xplore frame. Currently got a fox 36 on it. Was wanting to swap it out for a lyrik owned by a friend. Problem is its off of a remedy so tis got a tapered steerer ...
Started by LoveB on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at rotorburn):
Measure the internal diameter of your bikes head tube....
Unless your frame has a straight 1.5 headtube with reducer headset?? http://www.bikeradar.com/news/articl...d-tubes-25275/
you possibly can .
Or rather large peg, small hole.
Square peg, round hole.
|
Ask your Facebook Friends
|
With Tapered Quarter-Wave Tubes, can they be done with multiple drivers per enclosure/transmission line?
if so how does this change the design brief?
thanks.
Started by gafhenderson on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at diyaudio):
Brief: Not much but depends on....
|
|
KBS Tour C-Taper Shafts THP had a chance to speak with KBS about their C-Taper shafts at the 2012 PGA Show.
Started by JB on
, 14 posts
by 13 people.
Answer Snippets (Read the full thread at thehackersparadise):
In my Aerolite X Pinstripe Stand Bag:
- 910D2 8.5 so glad I upgraded! Driver: Ping G20 ... .
I am so intrigued by the C-Taper.
Matrix)
Boccieri HH 20 /23 (NVS Hybrid)
Bridgestone J40 Dual Pocket Cavity 5-9 (KBS C-Taper)
SCOR 4161 and Kim.
|
|
Is this an effective way to taper & WD or is this even a taper & WD? This may sound sooo simplistic, but when I get my next refill, my plan is to take my daily dose and simply continue to try to slowly expand the time in between doses. That's it. Nothing...
Started by HydroApe on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at opiophile):
I mean: Is this an effective way to taper & WD or is this even a taper & WD? Yeah,the two main factors in dosing are time THE....
Re: Is this an effective way to taper & WD or is this even a taper & WD? Yeah it's a taper.
|
|
Is there a collet that can be inserted directly into a 30 taper or do I have to use a collet chuck?
Started by lowCountryCamo on
, 13 posts
by 12 people.
Answer Snippets (Read the full thread at practicalmachinist):
I know this isn't the question, but I have two 30 taper machines, so I bought an SPI holder that takes the 100 collets I use on the 40 taper....
(i asked.
Thanks for the link, finally a source for iso taper collets, besides the deckel type.
|
|
Who successfully tapered while keeping a job?
Started by lost787 on
, 11 posts
by 10 people.
Answer Snippets (Read the full thread at benzoexodus):
Its been a battle!
Mike I am ....
I was then put on Clonazepam .5mg daily, and given a taper schedule% every 2 weeks.
I would actually withdraw" from Xanax use.
During my first taper, I was able to hold a job at a very high volume Starbucks.
|
|
Do you guys and gals every have little nagging pains during your taper that seem just to creep up?
Started by You're doing what? on
, 11 posts
by 10 people.
Answer Snippets (Read the full thread at runnersworld):
Actually, when I run less, I seem to get....
It's called age.
Pretty much all the time there's little aches and pains .
When I taper, when I don't taper...
Always! That is why I try to avoid tapering as much as possible.
Every time.
|
|
How to prevent taper crimp brass scratching?
Hi folks, when taper crimping my .45 ACP loads with an RCBS die, I commonly get some brass buildup or "plating" inside the taper crimp die, which then causes minor but persistent scratching of the cases. The...
Started by 45crittergitter on
, 25 posts
by 13 people.
Answer Snippets (Read the full thread at thehighroad):
taper crimp (I'm assuming you are using a seating die screwed down to provide a light taper from? (FWIW, I've been using the same RCBS carbide dies set w/ light taper crimp for 10+ years - 50,000 from crimping and buy a Lee ....
|
