|
I just received a used Blade 450 and was reading through the manual and setting up my transmitter. The manual recommends 10% throttle for every position in the throttle curve for throttle hold. Does anyone know why it would suggest this?
Started by jktravis on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at rcgroups):
I once set my throttle trim below the mid-point and then got bit....
Be careful.
Such as the stock Blade 450 3D, most users would probably agree that they use throttle hold as a safety mechanism and set the throttle hold curve to ZERO.
|
|
Hey,
What throttle cable do people use with 20vt's with corrado g60 hydro pedal box? My current one fits the 20v side perfectly, howevEer it doesn't fit so well on the throttle pedal side :/ I used the recomended cable for 20v conversions, but I assume...
Started by Drag20vt on
, 17 posts
by 3 people.
Answer Snippets (Read the full thread at com):
When you say half moon shape are you sure its not just the rubber gromet that has fallen apart... .
My cable connection part doesnt look like this (round with the grommit inside)
Mines a half moon shape instead the fitment is the same on the hydro pedal box .
|
|
Hey all,
I have a 06' K200S 6000k on the ticker and the issue that I experience is when closing the throttle all the way.The bike has always been this way since I've owned it. I've gotten very smooth at accelerating and deaccelerating but when I "completely...
Started by by firebirdn on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at bmwsuperbikes):
As you turn the throttle very slowly does the power come up instantly or after certain measure of a turn on the throttle? No there is no play in the throttle.I-accelerating so I don't give the....
Hi, is there a slack in the throttle.
|
Ask your Facebook Friends
|
Quote: : Quote: : FLAP 1 can someone tell us how to adjust the link want connect thanks Here ya go...straight from the service manual
Inspection
1. Place the transmission in the P (Park) position
2. Start the engine, and warm it up thoroughly.
3. Measure...
Started by GIFF-TURBO on
, 15 posts
by 12 people.
Answer Snippets (Read the full thread at rzrforums):
Locate the throttle cable adjuster just above the adjuster until 1/16" to 1....
Remove the seats and rear service panel.
Adjustment
1.
Measure the distance the throttle pedal).
Start the engine, and warm it up thoroughly.
Position
2.
|
|
Greetings!! Just bought our 2003 CTS back in February 120K, but we've got two other GM products with over 200K on them, so, expected to get 50-60K out of the CTS. So far, sorta good. Replaced timing belt (dealer) and serpentine belt expected repairs. ...
Started by JohnLentz on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at cadillacforums):
Got to get this thing....
I've got the Throttle body in September.
It will save your O2's & Cat cons.
But whatever you use make sure it is 'Sensor Safe' .
There is also Throttle Body Cleaner in a spray can.
Let us know the outcome.
Reconnecting.
|
|
Please note the time of this post
But
Would would happen if, I bolted a set of GSXR SRAD 750 Throttle bodies to a standard abf set up?
I.E. use the standard injectors and ecu, but use the tb's to manage the air flow!
Would the ecu cope?
Would there be...
Started by bigbenbird on
, 20 posts
by 8 people.
Answer Snippets (Read the full thread at com):
As said you can read load....
Obviously for the mechanical part you are going to need a TPS-throttle position sensor not be established further.
The first uses the throttle angle and the latter uses engine vaccuum of tuning.
Is the MAP mode.
|
|
Can some one confirm for the the type of throttle switch on a 2.0 gti please?
Is it a TPS (throttle possition sensor) or a idle/full load like on the mk2 8v gti engines?
Started by milesmk2 on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at com):
TPS Miles I'm sure you would be able to fabricate a mounting bracket to fit a idle/full load switch as required? .
|
|
The Throttle Firefox extension doesn't work on linux.
Is there a utility for linux that could throttle the bandwidth usage for a particular program/process, or even the entire system?
Main usage would be for web development, to test the user experience...
Started by hasen j on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at superuser):
The answers: how to throttle bandwidth on a linux network interface ..
|
|
Very good tip I thought my top end was feeling a bit flat. 32h and 504miles on it and it was never adjusted. Oh well I found my missing ponies.
Thanks for the heads up Junky!
Started by Buzzsaw46 on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at rzrforums):
Might to adjust the screw a 1/4 out.....
They thought that the throttle pedal had to be modified with more throw to be able to open the throttle 100%.
If you adjust the cable as far as you can you still only get 80-90% full throttle.
|
|
My Yardman will run at 3/4 throttle with pto engaged but stalls out when put at full throttle , any suggestions ?
Started by earlbear on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at lawnmowerforum):
Put water in a Windex bottle - at full....
It runs fineat full throttle without the blades running , as soon as I engage the blades it stalls out , if I set the throttle at 3/4 it runs fine .
Of the filter
it's simple fixes that take time ...
|
