|
TL;dr: "I am not sure how to calculate a smooth transition of thrust between one vector and another."
I am programming a simple game where an enemy chases after the player in an open space (no walls). I was calculating the enemy's x & y velocities independently...
Answer Snippets (Read the full thread at stackoverflow):
Similarly, by recognizing that acceleration (thrust) is simply a change in velocity equations:
F = m * a s = s_o + v * t + a * t^2 /....
You may get the effect you want by ensuring a smooth change in velocity , rather than thrust equiations.
|
|
What type of electric propulsion has or promises the highest thrust to weight ratio. Not counting the power source but counting the fuel density. Is it scalable to higher thrust?
Started by aero on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at nasaspaceflight):
Http://www.dtic.mil propulsion has or promises the highest....
Nomadd Full Member
Offline
Posts: 591
Location: New Jersey
Re: Electric propuslion thrust to weight thrust to weight ratio?
The Air Force had a pretty good rundown of technologies.
|
|
In an acrobatic plane, do I adjust the thrust line of the motor to be zero up/down and left/right?
Started by Zerts on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at rcgroups):
Just a bit of right....
The same goes for adjusting the CG to suit how you without any trim change .
You could start with everything zero-zero, then after a flight or two adjust the thrust line the thrust line fairly easily helps considerably.
|
Ask your Facebook Friends
|
There are different thrust washers for a 4pinion planetary compared to a 3pinion Frank
Started by fmerkl on
, 22 posts
by 5 people.
Answer Snippets (Read the full thread at network54):
Anyone....
I need to find someone who is familiar with the truck C6 and ask that question .
My a thrust washer where my transmission does not need it.
The free play difference I'm having is just about equal to the thickness of one thrust washer.
|
|
The End to Modular Thrust Bearing Failure >>
We thought we would post this as we have alot of people call in regards to failed thrust bearings, for those that havent seen this great product, the MMR TBS (thrust bearing system) replaces the factory...
Started by MMR Mustang on
, 11 posts
by 8 people.
Answer Snippets (Read the full thread at yellowbullet):
Thrust bearings generally are in the rear of the block? Re: The End to Modular....
Re: The End to Modular Thrust Bearing Failure >>
Are the bearings made in USA? Re: The End to Modular Thrust Bearing Failure >>
I don't follow.
|
|
I watched the video again and can see that my rear planetary is a four gear design (truck). This may explain why 2 of the thrust washer tangs on the rear thrust washer don't go into round holes. Both washers front and back fit flush against the planetary...
Started by flawebmaster on
, 23 posts
by 5 people.
Answer Snippets (Read the full thread at network54):
My shop manuals and Ken's video all show passenger car transmissions... .
There are different thrust washers for a 4pinion planetary compared to a 3pinion Frank Thanks play difference I'm having is just about equal to the thickness of one thrust washer.
|
|
Thrust Built Dasa 6 mil stroker, 930cc short block. Very low hours, very reliable, very powerful
$4700
Ricky B.
989.400.1902
Started by junebug on
, 17 posts
by 7 people.
Answer Snippets (Read the full thread at x-h2o):
Smoking deal.
I like that.
For nearly 1000cc Blood Red DASA from THRUST! Dope engine...blood red.
|
|
Quote: "This only leaves 3 thrust bearings that could be causing the problem. One behind the reverse ring gear , one behind the rear planetary and one in front of the rear planetary." Did this trans originally have a thrust bearing between the reverse...
Started by galaxiex on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at network54):
The rear planetary has a ....
I measured all the thrust bearings planetary.
I have not upgraded anything.
No hard parts.
I have replaced the thrust washers, clutches, steels, seals and gaskets.
The end play before I took it apart was .030 .
|
|
I am now convinced that I have added an extra thrust washer where one does not go. I am concentrating on the front planet. Another poster told me there have been a lot of changes in that area. I have two needle bearings on the front planet. One on top...
Started by flawebmaster on
, 11 posts
by 4 people.
Answer Snippets (Read the full thread at network54):
This only leaves 3 thrust bearings that could be causing the problem in the reverse clutch hub, so I believe the thrust washer behind the rear planetary is OK in that position housing which is on the transmission....
Planetary) in full contact.
|
|
Torque Thrusts Black Bought Torque thrusts black and within 11 months i have corrosion on all of them and 1 is getting severe on the outer polish alloy. , Wheels and been Looked after and COst quite a bit , Company jsut said it was down to poor maintenance...
Started by will20bristy on
, 15 posts
by 12 people.
Answer Snippets (Read the full thread at mocgb):
They were lighter, cheaper and definitely better quality with the torque thrust look.
What so ever.
|
