|
Put this together for an upcoming set of projects:
You Tube You Tube
Started by jdh239 on
, 14 posts
by 10 people.
Answer Snippets (Read the full thread at weldingweb):
One is the 1/2", I modified.
I have a couple sets of rollers besides the round die rollers for my HF tube roller a couple sets of rollers besides the round die rollers for my HF tube roller.
Then the heavy hitch tubing.
|
|
I have the original chinese Tube, what would you suggest I put in for a smoother
more mellow sound?
Many Thanks
Started by XLR2XLR on
, 21 posts
by 11 people.
Answer Snippets (Read the full thread at gearslutz):
I'd opt pre
for $14.00 - $36.00 your solution ....
A good tube will cost more than the pre, and probably won't change the sound much.
I don't really see the point of dropping an expensive tube into a cheap starved-plate preamp.
Improvement.
|
|
Hi trying to remove the handle bar tube from the head tube. Have soaked it endlessly with BP Blaster - I can neither shift the Handlebar tube or the nut holding the forks.
What if I saw through the nut? would that help?
Have probably made it worst by ...
Started by rubblequeen on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at ratrodbikes):
The the front forks and saw through the tube just above the bearings do you think that I would then be able to enable me to get it loose from the head tube?
The knurled nut holding the bearings in just won't) is hardened steel, you will....
|
Ask your Facebook Friends
|
Wed Sep 21, 2011 9:34 pm by Chauss
Tubes for CarverFest 11 Tube Amp Had a runaway tube as soon as I plugged in the amp to give it a play- For the EL84's I got the new "reissue" Mullards made in Russia- should be here tomorrow. Will post results upon listening...
Started by Chauss on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at carveraudio):
Thu Sep 22, 2011 2:24 pm by engtaz
Re: Tubes for CarverFest 11 Tube Amp Bob talked highly church use Thu Sep 22, 2011 3:53 pm by tinpan....
Wed Sep 21, 2011 10:08 pm by OconeeOrange
Re: Tubes for CarverFest 11 Tube Amp There were.
Related shopping results:
|
|
Currently I am using the Onkyo NR3007 receiver for HT and 2 channel Audio. I would like to try a tube amp just for stereo listening. Does it make sense to get a Tube power amp and feed it via the receiver preout or better to get an integrated tube amp...
Started by sportflyer on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at avsforum):
I would like to try a ....
Try a tube preamp first, you will make the SS amp sound like a tube amp and still.
So if you got money to burn go for it .
Tube amps are nothing like SS amps..
Your wasting your money on a tube amp.
|
|
Hi Folks!
This is my virgin thread. I think you will like it, but lease be gentle with me ;-)
I have prepared a small test for you of how different tubes change the sound of my fave compressor, the CL1b.
First off download the 50 meg file from my server...
Started by World Studios on
, 30 posts
by 10 people.
Answer Snippets (Read the full thread at gearslutz):
Regards,
Glenn Tabor
www.gat3.com Just out of curiosity, which specific tube was the "vintage Telefunken tube" you used? How old was it, was it NOS, had this tube been used before of the gear we carry in person, please....
The results.
|
|
Fri Dec 16, 2011 11:29 am by jjptkd
Tube integrated or tube separates? I've been kicking around the idea, for quite some time now, of trying out a tube amp on my Klipsch speakers. Is there any advantage to having separates or are integrated units just...
Started by jjptkd on
, 14 posts
by 5 people.
Answer Snippets (Read the full thread at carveraudio):
I have heard some really good integrated tube amps that sound just as good as separates: Tube integrated or tube separates....
Fri Dec 16, 2011 12:13 pm by treitz3
Re: Tube integrated or tube separates? In my experience factors.
|
|
Im thinking about putting my ET Streets back on and wanting to get thoughts about running tubes. I never ran them before, but I noticed one of my tires was going flat faster..Not sure if I had a small leak do to a rock or what but anyway..
What are the...
Started by 223HAWK on
, 20 posts
by 14 people.
Answer Snippets (Read the full thread at ls1tech):
The tube will help stiffen the sidewall up even more, I run the stiff sidewall with the tubes in them once I get the tires, but....
That im lucky it hasnt happend yet and I dont like the idea of putting screws in with the tube either.
|
|
Any opinion whether square aluminum tubing would be better/just as good for our truss tubes? There's this:
"The round tube is more efficient in compression and the square tube is more efficient in bending if the wall thickness and mass are the same for...
Started by killdabuddha on
, 33 posts
by 13 people.
Answer Snippets (Read the full thread at cloudynights):
Have you seen according to the following (and after doing a fixed element analysis):
"A practical limit for the tube aluminum tube....
1" round tube has less material than a 1" sq tube with same thickness.
tubes weight less.
|
|
TEIN, INC. | SPECIAL | MONO TUBE/ TWIN TUBE CONSTRUCTION, ONLY AT TEIN!
The structural differences between Mono-tube and Twin-tube.
These are the Mono-tube and Twin-tube shock absorbers you often find in magazines etc.
For those of you who have ever thought...
Started by jugbugz on
, 14 posts
by 6 people.
Answer Snippets (Read the full thread at ek9):
I have read that the mono flexs ride better than the Flex, will post up a comparison when we ... .
Are u refurring to?? Great post!
Have Tein HA's on my EK, Mono Tube, there pretty stiff! I love them bumps, not if they are twin tube or mono.
|
