|
Im thinking about putting my ET Streets back on and wanting to get thoughts about running tubes. I never ran them before, but I noticed one of my tires was going flat faster..Not sure if I had a small leak do to a rock or what but anyway..
What are the...
Started by 223HAWK on
, 20 posts
by 14 people.
Answer Snippets (Read the full thread at ls1tech):
Whats the $2 fix? I dont run tubes & both my slicks leak to crazy low air pressures....
The tube will help stiffen the sidewall up even more, I run the stiff sidewall with the tubes and I can help you fix it for $2 and no patches.
Either.
|
|
Hi everyone!
I am doing some research about amps as I am about to buy my first one in the near future
I am going for a tube amp, and I have a question regarding tubes.
What is the differences between amps that have tubes in the preamp, tubes in the power...
Started by Zeetwig on
, 8 posts
by 5 people.
Answer Snippets (Read the full thread at metalguitarist):
Nothing about the real difference...
And it was all about how the tubes change the signal and so on.
|
|
I rewrote that title 5 times and it's still not right.
Ok - so I have a nice tube integrated. But I'm reticent to turn it on if I only want to play a few cuts or just for a short time. I feel like it's bad for the tubes to be run up and down a lot for...
Started by Khodabear on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at audiokarma):
Running....
+ 1 Too much time in your the time.
If you wear out tubes, buy more and re-tube.
Use the tube amp.
If you wear out tubes, buy more and re-tube.
Use the tube amp.
Overthinking IMO.
|
Ask your Facebook Friends
|
I have a rather mathematical problem I need to solve:
The task is to cut a predefined number of tubes out of fixed length tubes with a minimum amount of waste material.
So let's say I want to cut 10 1m tubes and 20 2,5m tubes out of tubes with a standardized...
Started by Torsten Uhlmann on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
Some additional information and an online solver can ....
I believe you are describing the cutting stock problem.
Wikipedia has a number of references that might help you find clues to an algorithm that works .
This is known as the Cutting Stock problem.
|
|
Http://www.sjscycles.co.uk/sidewinder-s ... prod11127/
Whilst these are a great theory I have one question:
The concept is great, you don't need to take the wheel out to replace a tube, you just slide it in at the valve and then round until it overlaps...
Started by [XAP]Bob on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at ctc):
I wonder whether it is easy to ....
So it's a seriously screwed tube only replacement.
Then when one holes and deflates the second tube expands it in a destructive way and use the sidewinder.
It possible to fit two tubes in parallel.
|
|
I've noticed in several tube designs that sometimes the tubes used in tone control sections are heated with AC instead of with DC. Why does this not cause hum like it will with the other preamp tubes?
Started by Rod Beauvex on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at audiokarma):
|
|
Almost all of use have heard of Ted Stevens trying to describe the Internet with the analogy that it is a series of tubes ( mp3 ). I believe that it likely that some tech person somewhere tried to describe the Internet too him and this was the best analogy...
Started by Zoredache on
, 8 posts
by 8 people.
Answer Snippets (Read the full thread at serverfault):
Never ever type "Google" into Google !
Series of tubes.
People laugh at Ted Stevens, but "a series of tubes" isn't the stupidest way of describing inbetween."
-Adam
Remember kids...
|
|
Hi Folks!
This is my virgin thread. I think you will like it, but lease be gentle with me ;-)
I have prepared a small test for you of how different tubes change the sound of my fave compressor, the CL1b.
First off download the 50 meg file from my server...
Started by World Studios on
, 30 posts
by 10 people.
Answer Snippets (Read the full thread at gearslutz):
Go right ahead! You can expect the same improvements in most any tube gear the....
tube)
4 Vintage Telefunken tube (I only exchanged the input 12AX7 tube)
5 Mullard 4001 and 4004 tubes tubes in some of my gear...
|
|
I'm getting ready to buy some JJ 12AX7 preamp tubes and was just wondering where you guys and girls like to buy tubes from and why. I am looking at Euro Tubes, Tube Depot and Analog Tubes. They all seem to be about the same price. Is one place any better...
Started by premgem on
, 13 posts
by 12 people.
Answer Snippets (Read the full thread at strat-talk):
I am looking at Euro Tubes, Tube Depot and Analog in his tube kits(like he can say if you want overdrive earlier choose this one, etc?), the shipping is fast, and they pack well....
Guys and girls like to buy tubes from and why.
|
|
I am goin to a different setup this year an these are to big for me now. lookin to sell the injectors for 800 obo an the tubes for 80. or trade the tubes for .93's
Started by strokersmoker98 on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at cumminsforum):
An yes i am very interested in tradin those tubes, i believe i ve delt still have sticks So you are saying the feed tube on the injector is enlarged to .120"? Yes sir drilled or EDM'd the feed tube....
But they deff deliever the fuel.
|
