|
I just picked up an MP40wES for my standard 180 soon-to-be SPS dominated setup and am looking for some input on what my next step should be. The tanks glass is 1/2" thick, 2 island setup.
Basically, whats my better option as both will cost me roughly ...
Started by iLLwiLL on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at reefcentral):
Is the mp60 + mp40 combo favorable over....
I would personally go with one MP40wES and one MP60wES .
Two MP40wES pumps should work well.
Any other opinions on this?
~Will.
A pair of 40's should be fine IMO.
Or can I get away with just a pair of 40's?
~Will .
|
|
Got a bunch of stuff for sale as i'm trying to raise some cash for some new equipment.
for powerheads, I have a few koralia magnums . . .
(1) K8 - 3250 GPH - $75
(2) K5 - 1650 GHP - $50ea
(1) K5 - 1650 gph - 30 (will need to be sent in for repair, hydorUSA...
Started by iLLwiLL on
, 5 posts
by 2 people.
Answer Snippets (Read the full thread at reefcentral):
Bump, how about $220 for everything powerhead related (4 pumps and... .
Dews, 1 green cap and purple cap (can make 1 more piece that size) - SOLD!!
~Will .
Pm sent 1 RBTA, big toadstool, eagle eyes, gorilla nipples, mt .
~Will.
Bump, feel free to send offers.
|
|
Posted Yesterday, 08:06 PM
I'd like to save the main pending UFA's (Gill, Moen, and Kostitsyn) for closer to the deadline so that leaves us with discussing Yannick Weber's future this week for our ATB article. There is lots to ponder with him...
- Should...
Started by dlbalr on
, 10 posts
by 6 people.
Answer Snippets (Read the full thread at habsworld):
Posted Yesterday, 10:17 PM
illWill, on 24.
Do so as part of a package to land a bigger asset .
|
Ask your Facebook Friends
|
Well it's coming to that time where the cycle is winding down on my new setup. So my question is twin mp10's or a single mp40? I can't afford to do two mp40's up front. The tank is a 30x30x24 cube that's 93 gallons. Will be a 50/50 of softies and sps
Started by Amdeus on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at reefcentral):
I would get....
Wish I had never added them.
It is costing me about $1000 to remove the softies out of my 360g reef .
It can be done but it can also be a real hassle .
Softies will use chemical warfare on your hard corals.
I would reconsider softies and sps.
|
|
I currently have a hodge podge of powerheads in my 180 and I would like to clean it up and upgrade to a couple vortechs. The tank is a standard 180 with corner overflows, 2 island scape with a lot of SPS, soon to be even more. I currently have a wavemaster...
Started by iLLwiLL on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at reefcentral):
When i was shopping for flow, i was looking....
In my personal experience two mp40s will not be enough for your tank .
Depends on what you want to keep, 2x40's may be enough flow for a softie or mixed, but just two may be hard to aim w/out having any dead spots .
|
|
Hey gang,
Having been a 10+ year reef nut I've been around the block a few times when it comes to marine system care. All aspects...
Anyways...past two months I've spent countless hours setting my system back up... Got all the gizmos you could think up...
Started by Reistroffer on
, 22 posts
by 14 people.
Answer Snippets (Read the full thread at reefcentral):
For that kind of money I would have just supported... .
Was everything WYSIWYG, or were there specific sizes advertised? Those prices seem very, very high (live aquaria prices are around half what you paid) .
Send the vendor an e-mail explain your issues.
|
|
WHAT DOSE U RUN?
HOW LONG U RUN IT?
RESULTS?
THX BROS.
Started by Arnold jr on
, 21 posts
by 11 people.
Answer Snippets (Read the full thread at getbig):
|
|
Looking to sell a Brand new complete CSL/ZCP brake set. Specs taken from Turners website:
Genuine BMW front rotors - cross-drilled and floating - 345x28mm
Genuine BMW rear rotors - cross-drilled and floating - 328x20mm
Genuine BMW front and rear calipers...
Started by ILLWILL on
, 9 posts
by 8 people.
Answer Snippets (Read the full thread at m3forum):
Isnt this the 2nd....
Thanks.
You have a PM! $1,350 with the lines?
Ready to pay .
Great price OP! GLWQS! You should be good to go .
WOW! $3,000+ from Turner for this kit? My how times have changed .
Bump! If you wanna sell just the front rotors PM me please .
|
|
Can some one tell me the differents in these headers? Cuz one is 10 dallors more then the other. one says throw fire wall and I don't know exactly what that means
Racer Walsh Race Step Header 2.3L thur firewall 1 5/8"
Race Header 2.3L
Started by ILLWILL on
, 6 posts
by 4 people.
Answer Snippets (Read the full thread at moddedmustangs):
Thats what i was thinking and i dont want that Ill : first trick i picked up here two days ago....94-95 ranger exhaust... .
Mostly for circle track racers.
It means you have to cut a hole in the firewall and the exhaust goes where the passengers feet would be .
|
|
This isnt realy a question. I was just wondering if any body els has noticed that ther are way more 4cyl notch mustangs then 5.0 mustangs. Has any body els noticed that or is it just me?
Started by ILLWILL on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at moddedmustangs):
I dont like hatches so ive been....
I thought it would just be cheaper to buy one done already .
I have a 87 4cyl notch mustang and i was gonna do a 5.0 swap .
But tons of 5.0s.
At least not that I can remember.
Ive never actually seen a 4 cylinder mustang.
|
